Home

Gap between tub and floor tile

Need help with a 2 inch gap between my new tub and the tile floor! Comments (4) Find a good tile person, They can remove the grout and replace the tiles along the tub. I have done this myself and not had a problem cracking the abutting tiles. Also, the one tile that is against the tub has a bad jagged cut Find a good tile person, They can remove the grout and replace the tiles along the tub. I have done this myself and not had a problem cracking the abutting tiles. Also, the one tile that is against the tub has a bad jagged cut. Make sure whoever does this gives you a clean cut with a good saw for doing so Answered My bathroom tile is ceramic, and was clearly installed poorly, there is about a 3/4 to 1 gap between the tub and the floor tile, it currently has caulk to fill the gap but that always get dirty and separates over time. I'm just looking for options, (Please dont suggest to retile, as that is not an option for now) 4 answer

What would you do for gap between tub and floor tile

  1. or shifts between the bathtub and floor put stress on the bathtub caulking joint. No matter what type of floor installation, this bathtub gap needs to have the caulking..
  2. Similar to the gap that can exist between your wall tile and tub, you may have a space between the floor and your bathtub. This gap may widen over time as your home shifts. As with any other gap near your bathtub, you'll want to close the opening to prevent any possible water damage or the onset of mold and mildew
  3. large gap between tub and floor. I am laying down new tiles, and I have about a 1.5 inch gap between my tub and the floor. I was thinking to put a peice of quarter round on top of a 1x3, but now I'm thinking it may not be a good idea -being wood and all. Don't want moisture problems
  4. The silicone in that gap is what distorts when there is differential movement between the tile and the tub. And forcing all that distortion on a small 1/16 gap is too much for me. The bigger the gap, the more silicone there is available to distort. I'd go with an 1/8 gap
  5. 1/8. Between floor and wall or other abutting dissimilar material, 1/4. wall to wall-inside corner, wall to tub about 1/8. All those intersections get caulked and stay clear of grout and thinset, although where tile ends 1/4 from wall or pip that will be covered by mouldings or something else can be left clear of anything

Get a piece of vinyl/PVC trim in the millworker aisle and some silicone adhesive. Cut the trim to the length of the tub. Apply the silicone adhesive to the back and bottom edge of the trim piece. Place on the tub using boards to put pressure on the trim, while also pushing down so that the trim meets the floor Got another idea from the additional posts: consider cutting out a stip at the bottom of the tiles coming down to the tub, say 4 (or whatever you think will work aesthetically). Then cutting 3 1/2 pieces to fit in the empty spaces. That'l leave 1/4 for grout, and 1/4 for caulk

Need help with a 2 inch gap between my new tub and the

Idea for gap between the tub and floor tile Hometal

Fill gaps up to 1/4 inch in width with caulk. If you have tile on the wall adjoining the tub, select a caulk that matches the color of the grout. If your gap is smaller than 1/8 inch in width, use.. Ive since picked all the silicone off which has left about over 1 cm gap between the tiles and the bath there is no bottom to this gap as you can see right down to the floor, this gap doesn't go the full length of the bath . The tiler has grouted down in most areas but not behind the the taps (it's s double ended bath so the taps are in the.

How to Fill the Gap Between the Bathtub & Flooring Home

Leaving a 1/16″ gap between the tub and tile will prevent the tile from cracking when the tub expands. Plus, a 1/16″ gap allows the caulk to properly fill the space and waterproof the transition between the tile and tub or shower. Place the 1/16″ horseshoe shim on tub and measure up to the laser level http://www.homebuildingandrepairs.com/bathrooms/index.html Click on this link for more information on bathroom design and remodeling. If you have a gap betwe..

Ask a Handyman: Should You Grout or Caulk Around Tub

Large Gap Between Bath And Tiles. Large gap between tub and tile 1 2 seal a gap between tile floor gap between tub and tile caulking a bathtub with various size caulking a bathtub with various size. How to fill a large gap between tile and shower tub ensure installing a tub need advice on 1in gap between end of the tips for a small bathroom uk. The D.I.Y video How To Seal A Big Gap Between Tile Floor And Tile Wall In A Bathroom Or Shower. It shows how to seal a gap in the corner where the tile floo.. A: In general, grout is the right filler between tiles on a wall or floor, and caulk is for joints where tiles meet a tub and where tiled walls meet at a corner.Your situation involves each of. In addition, leave a 1/16″ to 1/8″ expansion joint between the main wall tile and shower floor tile or adjacent wall tile. This joint should then be filled with 100% silicone to allow for expansion and contraction as well as providing a waterproof layer. Hopefully these tips help you with your project Gaps up to 1/4 Inch If you have tile on the wall adjoining the tub, select a caulk that matches the color of the grout. If your gap is smaller than 1/8 inch in width, use regular caulk; fill gaps larger than 1/8 inch with a sanded caulk

large gap between tub and floor - DoItYourself

Where my tub meets my tile floor the tub edge is unsupported. The tub itself is set in foam but the outside edge does not rest directly on the floor since I installed the tile after the tub was in. There is barely a gap between the floor and tub, maybe 1/32 to 1/16 at the most Technically, after the tile is installed over the backer board that gap between it and the tub ledge should be filled with an ASTM C920 sealant (caulking e.g. silicone). Although some say you should have weep holes along this gap so any water behind can weep out into the tub

How do you fix a big gap between tub and floor? Fill gaps up to 1/4 inch in width with caulk. If you have tile on the wall adjoining the tub, select a caulk that matches the color of the grout. If your gap is smaller than 1/8 inch in width, use regular caulk; fill gaps larger than 1/8 inch with a sanded caulk Gap between floor tile and tub. Lay several porcelain tiles in a row using spacers to simulate joints. Lay several porcelain tiles in a row using spacers to simulate joints. From portable dance floors to basement flooring to dance flooring this multi use tile is an excellent choice for countless projects Also, make sure the gap between the tub and floor is optimal. Otherwise, you'll have to close the extra gap between floor tile and tub. This is a pretty easy method when it comes to leveling the stud walls. But there are some calculations. You might have to do them a couple of times till it gets fixed How do you fill a large gap between tile and wall? If you have tile on the wall adjoining the tub, select a caulk that matches the color of the grout. If your gap is smaller than 1/8 inch in width, use regular caulk; fill gaps larger than 1/8 inch with a sanded caulk

Generally speaking, you should be able to seal and fill those ¼ inch gaps between the wall and tub with one bead of caulk. Be aware of the color of your wall or tile. For tile specifically, pick a caulk that will match up with the color you used for the grout. Keep in mind: if you have a gap that is smaller than 1/8 inch, you can use regular. Gaps between caulk, tub and tile - If you have gaps in your grout or caulk, shower spray or bath water may be seeping into the walls and subfloor, causing mold, mildew and wood rot. Spongy or soft floor - If your home was built with a wooden floor truss system, the sub floor is usually made of plywood, which forms the actual floor of your home The tile is 8 by 12 and is thicker than smaller tiles. To leave a 1/4 gap between the tub and the edge of tile nearest backerboard meant that the front face, the finished face of the tile, protruded far enough away from the wall that the gap between the front edge and the tub was 3/8 to 1/2 3 Ways To Cover Gaps Between Tile And Shower/Tub Faucet Trim Kits: 1. Fill In The Gaps Between The Tile And Trim -. One possible solution to fill the space would be to use grout or caulk. We have found this to work best when the tile and grout are a similar color and the gap is a half inch or less. Unfortunately, if you have contrasting colors. Re: large gap between tile and tub; Author: hj (AZ) If there is a 1 1/4 gap between the tub and the tile, I might want to stay out of the tub, because it may be ready to fall through the floor into the basement. The only way there could be that large of a gap is is if the tub has fallen that amount already

Proper size gap between tile and tub [Archive] - Ceramic

Recommended spacing between tile and bathtub - Handyman

Spread ceramic tile mortar on the back of the cut tile and set it in place next to the tub, properly spaced with the surrounding tile. Leave 1/4 inch of space between the cut side of the tile and the tub. Repeat for each tile around the tub. Let the tiles set overnight. Advertisement Cement Board Detail. above the lip of the tub. Then apply a generous amount of thin-set to the bottom bathtub tile and position it 1/8 in. above the tub. Fill the gap between the tile and the tub with caulk. Click to see full answer I have been trying to decide what do do with the gap between the hardibacker (red guard applied) and the mud shower pan. Second question is the debate on whether to caulk or grout the gap between the wall tile and shower floor tile. I am worried about creating a water damn of some sort Shower - How to fill a large gap between tile and shower tub to ensure waterproof gap. caulk floor shower. I incorrectly tiled my bathroom walls, leaving a 3/8 inch gap between the subway tiles and the shower floor tub. I have purchased some back rod roll to help with caulk fill ANSWER ANSWER - The polyethylene backer rod is not likely the cause of your cracking at the tub to shower wall transition, but if there is room for it in that joint, then you should use it to fill the excess space and to gauge the thickness of the sealant you are using. Generally the transition between the tub and tile on the wall is either wrongly filled with cementitious grout or the.

with tiles of adjacent tub or shower surround. If new flooring will be installed, leave a sufficient gap between lowest tile and subfloor. level line level horizontal starting line floor tile vertical starting line On bathroom floors, start by placing full tiles in front o Looks like it would work OK but had to return it as it is definitely no more than the 1/2 described - I was hopping it would fit around the base of a curved shower tray that (due to the floor not being level) has a gap between the floor and the base of the tray that goes from virtually no gap to just over 1/2 - unfortunately it did no fit It's one thing to read a step-by-step tutorial regarding DIY projects such as retiling a tub surround, and another to have your project go as perfectly as it does in said tutorial. The truth is, when you get into a project you'll likely identify ways your project is different, and many times that means challenging Leave a gap between the tile and shower floor. Use spacers to maintain a consistent gap. Allow the area to dry until the mortar achieves its initial cure and the mosaic tile becomes solidly bonded. Note: If your shower bottom is a one-piece acrylic factory-molded shower floor, leave a gap between the mosaic sheets and the top rim. Use spacers. In any shower areas between the tiles and non-tile surfaces caulking should always be used. Where tiles butt up against non tile surfaces there will typically be a lot of movement between these surfaces. Where tiles are installed around a bathtub the bathtub will move up and down when water and people are present in the bathtub

Floating Floor Against Tub, How To Seal? DIY Home

Unfortunately, too many tile installers — even good ones — still assemble showers in ways that almost guarantee failure and very quickly. Incorrect shower tile installations have a major tell: The corner grout joints have obvious, unsightly cracks where the walls meet the tub and each other Once I got the crappy self-stick DIY vinyl tile and it's adheasive off the original tile, the 50's mosaic tile floor looks very nice. However, in the process, I've removed ropes of silicon caulk from around the floor's borders with the wall tile, and I now have a fairly uniform 1/8″ gap between the edge of the tile floor and the j. 16943. make sure bath is fixed securely pump mastic down sides of bath that touch walls level with top of bath when set tile down to bath leaving a 5mm gap between tile and bath when tiles are set seal 5mm gap with coloured waterproof mastic of your choice. 2012-04-04T09:20:04+01:00 Buy Red Devil 0170 (Wide) Tub & Floor Caulk Strip, 1-1/4 x 5', The scoring is more like on the bottom 1/6th of it. It barely covered the biggest gap in the flooring and I have doubts that it will stay adhered for long. Read more. 3 people found this helpful. Helpful. Rust-Oleum 7860519 Tub And Tile Refinishing 2-Part Kit, White, Single. Edit: The gap is between the wood flooring and the metal edge along the side of the tiles. That dark part that looks like a gap on the tile side is either grout or some other discoloration/dirt. Maybe it will wipe off, who knows

The plank flooring provides you the same luxurious look, and it is much more cost-effective. Vinyl flooring is typically much more comfortable to install with either a click-together, glue-down, or loose lay type of installation. When floor gaps occur, it should be easy enough to fix No matter what gap you're trying to close up. Let it be between a tub and floor tile or dishwasher and countertop, the first task is to measure the gap. And to measure the gap you'll need a measuring tape. Simply hold the tape near the gap and it'll tell you the size of the gap Gap between shower floor and wall tile. We have a dry basement with a concrete floor. The diy video how to seal a big gap between tile floor and tile wall in a bathroom or shower. So to accommodate the flooring tile many like to leave a small gap between the last row of wall tile and floor Use when installing bath fixtures to seal gaps between shower tiles, between sinks and counters, and around the base of the toilet. Use outdoors in areas exposed to direct sunlight or rain, as the silicone helps the seal last longer. In older homes: Seal where any siding overlaps the foundation to prevent air from entering

Grout Lines for Floor Tiles. As a general rule, floor tiles should have grout lines of 1/8 inch or larger, depending on the type and size of tile. Special types, such as slate or quarry tiles, often do not have edges uniform enough to work with tight spacing. These tiles usually are spaced with grout lines 3/16 inch or wider The proper way is to leave a 1/8 inch gap between tile & tub. Fill the joint with backer rod then caulk with 100% silicone. The silicone joint is supposed to be twice as wide as it is deep. That's the by-the-book way of treating that joint

Shim the backer board up off the tub surround by about 1/4 inch, which leaves enough room to caulk the gap between the tub and the tile along all three walls. Use ceramic coated screws, usually on the shelf near the backer board, to fasten the pieces in place Choose the correct type of grout based on the width of your tile joints and the location of the repair. Measure the space between the tile. If the space is larger than 1/8 inch, use sanded grout. If the width is 1/8 inch or smaller, use unsanded grout. Never use sanded grout with metal, glass or marble tile. The sand will scratch the surface Apr 11, 2007. #5. [. 1) The tile supplier said that the tiles look best 'without any joint' (I assume he means butting tiles together completely) as they just form a single expanse of marble look floor. He said that if a gap was required then it should be 3mm absolute maximum ideally 1-2mm Once the tub is in place look into the open front of your deck at the gap between the bottom of the tub and your floor below the tub. You want somewhere around a 1 gap. If the gap is a few inches, use scrap plywood, 2 x 4, 2 x 6, whatever is needed to build up the floor to reduce the gap to about that 1

gap between tub and floor - Ceramic Tile Advice ForumsHow To Recaulk A Bathtub - Making ManzanitaSmall crack/gap in tub & tile - DoItYourself

Installing cement backerboard is one of the more popular choices for a shower wall substrate. Cement backerboards include Hardiebacker, Durock, Fiberboard, wonderboard, and similar products. These materials bridge the gap between expense and effectiveness. When installed properly they will give you many, many years of durable shower construction Apart from caulking, you can also make use of floor repair kits, which are quite similar. Coconix Floor and Furniture Repair Kit is one such product that comes with a putty-like substance that can be used to fill gaps between vinyl planks as well. In addition to this, it also comes with ten different shades of colors that can help you get the exact color and design of your vinyl floor Two-inch tiles are factory spaced and sheet mounted; therefore, the spacing is predetermined and usually averages 3/16 to 1/4 inch. Four-inch tiles -- called 4-and-a-quarter in the tile trade -- feature built-in, self-fitting nubs that give the tiles spacing between 1/16- and 1/8-inch wide. On one hand, 4-inch tile nubs speed up installation.

When grouting the backsplash tiles, leave the gap between the granite and the tiles empty. Grout is inflexible and will crack if pressure from the counter is placed against it. Instead of grout, fill the expansion joint between the tiles and the countertop with a latex caulk that matches the color of the grout Is the gap the same on all three sides? Or is the tile flush at the outside ends and gradually gaps to the corners and along the back wall? If it's the first scenario the tub was set level and the tile man started the tile a little high, because the lip on the tub is no more than a 1/2 In the winter is dries out and shrinks. This movement is manifest throughout your home--wood flooring gaps change seasonally, crown molding miters open, etc. etc. If your tub is framed with wood studs (or your floor, for that matter), the gap between tub and tile will open and close seasonally Consequently, how do you fill a large gap between tile and wall? Fill gaps up to 1/4 inch in width with caulk. If you have tile on the wall adjoining the tub, select a caulk that matches the color of the grout. If your gap is smaller than 1/8 inch in width, use regular caulk; fill gaps larger than 1/8 inch with a sanded caulk When you tile around a tub with a lip, leave a ¼ gap between it and the cement board. Use a thick layer of silicone caulk to secure the tub to the bottom row of tiles. When you go over the tiling with grout at the very end, apply one more layer of silicone caulk at the bottom of the tiles

Large Gap Between Bath And Tiles | Tile Design IdeasDIY Tub Skirt (Decorative Side Panel) For A Standard Apronfloor - How to fill a large gap between tile and showerThe Best Large Gap Between Vanity And Wall | Decor

How do you install LVP floating floor beside the bathtub? Is there a trim to cover the gap? Is this flooring a good choice for the bathroom? First is properly waterproofing the subfloor so if any water or moisture does migrate under the floor cove.. I have a tile tub surround, and old caulk that's gone bad which I've been planning to have replaced. The joint/gap is pretty wide though (probably a faulty installation on the tiles, which were there when I bought the house). Should I really leave a great big (at least 1/4 inch) gap above the tub without any sealant? Reuben Saltzma To scribe, place the plywood against the tub, adjust a compass to the width of the widest gap between the tub and plywood and while holding the point against the side of the tub, slide the compass. between tiles. (Marazzi products have integral spacer lugs so tiles can be butted together leaving a consistent 1/16 joint automatically.) If this layout leaves cuts smaller than 1/2 tile, adjust center line 1/2 tile closer to the side wall. Next, determine the lowest point of the floor or tub, using a level horizontally. Stack two tiles here, an Gaps are usually 5/16 between the outside edge of the floor (the perimeter) and the obstruction (see featured image). The gap is always hidden by a piece of trim molding, like a quarter-round or a transition. Against metal doorframes and areas where you cannot install a molding, use a color-coordinated silicone caulk to fill the gap and.